Looking for a 200 kW screw air compressor in Sri Lanka? Contact Vortex Axion to discuss a Vortex Pneumatics enquiry for large plant utilities. This guide covers integrating a compressor with plant electrical capacity, the 200 kW screw air compressor price enquiry, air treatment and installation planning. Choose the offered model by its delivered airflow and pressure, then confirm the complete package in writing.
200 kW screw air compressor price in Sri Lanka
The 200 kW screw air compressor price depends on the selected model, control system and installation scope. Request a quotation in Sri Lankan rupees that separates the compressor from the dryer, air receiver, filtration, piping, electrical work and commissioning. Confirm taxes, delivery, lead time and payment terms in the offer. This capacity guide is an enquiry page; model availability and any stocking arrangements must be confirmed with Vortex Axion.
For large plant utilities, an equipment-only comparison can miss important project costs. Send your location, production schedule and existing compressor details with the enquiry. Ask each supplier to quote the same required airflow, pressure and air-quality specification, so the prices describe comparable systems. A lower motor rating or cheaper machine may be unsuitable if the specified operating point cannot be met.
Integrating a compressor with plant electrical capacity
A large air-system upgrade needs coordination between production, maintenance and the electrical team. Motor power is only one part of the supply assessment.
Have the proposed starting method, drive arrangement and electrical ratings reviewed against the site’s available supply. Include auxiliary dryer and ventilation loads in the assessment.
A 200 kW offer should state the model’s supply requirements and installation responsibilities. Cable routing, protection, transformer capacity and starting behaviour should be assessed by qualified professionals.
What to specify for a 200 kW screw air compressor
The 200 kW motor class is commonly described around 270 HP in supplier catalogues; HP labels are approximate and vary by convention. Motor power alone does not establish CFM output. Ask for the exact model’s free air delivery at your required working pressure, plus the rating conditions and control range. Do not transfer a manufacturer’s airflow figure to a different machine simply because both carry a 200 kW label.
Supply a measured or calculated demand profile, including minimum load, normal production and simultaneous peaks. Explain the pressure needed at the equipment inlet and any special air-quality requirements. If the plant has existing compressors, list their model numbers, operating settings and intended role. An application review should consider whether the proposed capacity will operate alone, replace an existing unit or join a coordinated system.
Compare controls and running costs
Ask which fixed-speed, variable-speed or two-stage configurations are available for the proposed duty. Compare published input-power and airflow data at equivalent conditions. Assess running costs using expected loaded hours, low-demand periods and maintenance requirements. Request a documented comparison rather than a universal energy-saving percentage; the outcome depends on the offered machine and the site’s actual load profile.
200 kW screw air compressor with dryer and receiver tank
The illustration shows a compressor, refrigerated air dryer and vertical receiver as separate components. Dryer selection depends on delivered airflow, pressure, inlet temperature and required dew point. Receiver volume should be calculated for demand fluctuations and the control strategy. Filtration, drains and condensate arrangements should follow the process requirements. The pictured accessory sizes are illustrative and are not a sizing recommendation for a 200 kW installation.
Include the proposed model’s electrical supply, starting method, cooling arrangement, dimensions and service clearances in the technical offer. Have electrical capacity and protection assessed by qualified professionals. Agree on unloading, equipment positioning, ventilation or cooling-water responsibilities, installation and commissioning. Review warranty conditions, maintenance intervals and spare-part support before ordering.
Compare nearby compressor capacities
Review the 185 kW screw compressor guide and 220 kW screw compressor guide before choosing a power class. You can also browse the complete electric compressor size guide, lubricated screw compressor range and maintenance services. These pages support selection; the final choice should follow your measured demand and the offered model’s performance.
200 kW screw air compressor electrical project brief
Treat the 200 kW screw air compressor enquiry as a coordinated utility project. Explain whether the machine will replace existing equipment, serve a new production line or join an established compressor room. Give the supplier a clear description of when it is expected to operate and which other major plant loads share the proposed supply. A purchasing brief that includes those operating conditions is more useful than a motor-power request alone.
Ask the factory’s responsible electrical professional to provide the relevant supply information and identify what still needs assessment. Keep the actual offered model’s voltage, frequency, input requirements and starting method attached to the proposal. The power category on this page is not a cable, breaker or transformer selection. Those choices require the machine documentation and a review of the site’s installation conditions.
For the 200 kW screw air compressor, agree which party supplies equipment information, which party designs the site connections and who signs off the completed work. Name a project contact who can coordinate purchasing, maintenance, production and electrical questions. This avoids ordering a machine while assumptions about supply readiness remain unresolved. Keep revisions to the operating brief visible to all parties reviewing the quotation.
200 kW screw air compressor model and supply information
Request a model-specific technical schedule rather than a general brochure covering several machines. It should identify the quoted configuration, available control features and the information required by the installation team. Ask the supplier to distinguish confirmed data from items awaiting manufacturer confirmation. Purchasing should be able to trace the specification back to the exact machine in the offer without combining values from different catalogue rows.
Provide the production duty and required airflow at the intended operating pressure with the enquiry. A 200 kW screw air compressor label does not establish delivered CFM or the conditions at distant production equipment. Ask how the offered performance is expected to meet the application, and document any assumptions about demand. If measurements have not yet been taken, identify that as a selection task instead of inserting an unverified airflow figure.
Discuss the expected starting and operating arrangements using the offered manufacturer’s documents. Ask which auxiliary equipment is included and which has a separate supply or installation responsibility. The dryer, control equipment and any quoted cooling auxiliaries should appear in the project equipment list. Their requirements should not disappear from the site review merely because the compressor is the largest item in the package.
Coordinate the 200 kW screw air compressor with factory utilities
Prepare a simple plan showing the proposed equipment location, access routes and relevant existing services. Identify other work taking place in the same area and the periods available for installation. Ask the responsible professionals what information they need from the supplier to assess the proposal. A site walk can reveal missing project information, but it is not a substitute for model documents and an approved installation design.
For the 200 kW screw air compressor project, record the boundary between the supplier’s package and the factory’s utility work. State who is responsible for routing connections, preparing the equipment area and confirming readiness for commissioning. If an upgrade to existing infrastructure is under consideration, obtain its separate scope and schedule. Do not assume such work is included in an equipment price unless the quotation says so.
Describe the plant’s normal operating timetable and any occasions when multiple major machines start together. The electrical team can then review the relevant conditions using the supplied model data. Avoid deciding suitability from a single observation taken during a quiet period. Where the review identifies additional requirements, have them reflected in the project budget and delivery plan before committing to a commissioning date.
200 kW screw air compressor controls and operating responsibilities
Ask how the proposed compressor will be started, stopped and supervised during normal shifts. Identify whether it will run independently or receive commands from a wider plant control arrangement. Confirm which interfaces and control equipment are part of the offer. An available interface in a brochure does not mean integration, programming or installation is included in the quoted work.
A 200 kW screw air compressor may be proposed in different control configurations, depending on the offered range. Ask for a written explanation of why the selected version fits the site’s demand profile. Compare performance at equivalent conditions when assessing alternatives. Do not assume a particular control type guarantees a stated energy saving or can cover every low-demand period without reviewing its documented operating range.
Agree who can change the operating settings and how approved changes are recorded. Keep operating instructions accessible to the authorised team and distinguish routine operator tasks from service and electrical work. If the system joins existing compressors, document their intended roles as well. The commissioning handover should explain the selected control arrangement rather than leaving the factory to infer it from the cabinet display.
200 kW screw air compressor dryer and receiver package boundary
List the compressor, receiver, dryer, filtration and other quoted accessories individually. Ask the supplier to state the conditions used to select treatment equipment and the air-quality requirement it is intended to meet. The process owner should confirm any special application requirement. A pictured dryer or vessel is an illustration, not evidence of its suitability for your flow, temperature, pressure or production process.
For the 200 kW screw air compressor with a dryer and receiver tank, request a project schematic and equipment schedule. Confirm the actual supplied configuration and any components proposed for reuse. The visual arrangement on this page shows the compressor, tank and dryer clearly; the final piping and treatment design should come from the agreed project documents. Do not use the image to determine receiver volume or the sequence of every filter.
Discuss access for accessory maintenance, drains and condensate handling with the installation team. Ask how treatment equipment is taken out of service and what that means for production. An isolation or bypass arrangement needs a process review rather than an assumption that untreated air is acceptable. Include accessory utility requirements and commissioning responsibilities alongside those of the main machine.
Compare the 200 kW screw air compressor price in Sri Lanka
Ask for a 200 kW screw air compressor quotation that distinguishes the equipment price from site work and accessories. Confirm the currency, taxes, delivery arrangements, unloading, positioning and commissioning scope. Where the factory supplies electrical or piping work separately, show those exclusions clearly. Comparing totals without comparing inclusions can hide a substantial difference between two offers.
Request the offered warranty terms and the maintenance requirements for the exact model. Ask which inspections, consumables and service tasks are included in any proposed support agreement. Have any promise about response times, spare-part availability or local stock confirmed in writing. This enquiry page does not establish a particular warranty period, stock position or guaranteed service attendance.
Assess operating-cost estimates using the documented model performance and a stated production schedule. Keep estimated inputs separate from measured factory data. Include any relevant quoted auxiliary equipment when defining the comparison boundary. A motor rating alone does not provide a complete electricity-cost forecast, and a general percentage improvement is not a substitute for a site-specific explanation of the proposed system.
200 kW screw air compressor delivery and acceptance planning
Agree on the information required before equipment is released for delivery. The approved location, access arrangements, work boundaries and supply-readiness tasks should have named owners. Ask for the actual machine dimensions and handling instructions. Make sure the receiving team understands the unloading and positioning scope rather than assuming the delivery contractor will complete every installation activity.
Before commissioning the 200 kW screw air compressor, agree which checks and records establish acceptance of the quoted scope. Identify the production conditions for relevant performance observations and the people authorised to witness them. Qualified professionals should complete the site assessments and work within their responsibilities. Commissioning should not proceed on the assumption that a nominally similar old installation proves the new machine’s requirements.
Keep the equipment schedule, approved operating values, supplied instructions and service documents together at handover. Record outstanding items and the person responsible for closing them. Include the actual model and serial numbers so later service enquiries can be identified accurately. A clear handover makes the installation easier to operate and maintain after the project team has left.
Free site inspection for a 200 kW screw air compressor
Prepare a room plan, current equipment details and the factory’s operating schedule before arranging a free site inspection. Identify the proposed connection point and the person responsible for electrical questions. Tell Vortex Axion whether the site is operating, under construction or being expanded. This helps focus the visit on the information needed to prepare a useful equipment and installation proposal.
Call 0777 123 263 to discuss your 200 kW screw air compressor requirement in Sri Lanka. Ask for a written follow-up identifying the proposed scope, missing technical information and selection steps. The inspection supports planning; the final order should still use the offered manufacturer’s documentation and the agreed responsibilities for electrical assessment, installation and commissioning.
For general background on reviewing industrial air systems, see the US Department of Energy compressed-air resources. These resources do not describe a confirmed Vortex Pneumatics model for your site. Use them as background while basing the equipment decision on the factory’s requirements and the exact technical offer.
Frequently asked questions
How much air does a 200 kW screw air compressor deliver?
CFM depends on the exact design and operating pressure. Request the manufacturer’s free air delivery figure for the model in your 200 kW quotation, rather than selecting from motor power alone.
Is this capacity suitable for large plant utilities?
Have the proposed starting method, drive arrangement and electrical ratings reviewed against the site’s available supply. Include auxiliary dryer and ventilation loads in the assessment. Suitability must be confirmed by comparing the proposed model’s performance with those requirements.
Does a 200 kW package include a dryer and tank?
Inclusions depend on the offer. Ask for separate equipment descriptions, accessory capacities and installation responsibilities. The picture does not establish the supplied scope.
How can I request a 200 kW screw air compressor price in Sri Lanka?
Send your site location, air demand, pressure, operating hours and electrical supply details. For this project, also explain integrating a compressor with plant electrical capacity. Vortex Axion can discuss the enquiry and confirm the proposed package, price and lead time.
Request 200 kW screw air compressor quotation
Free site inspection: Contact Vortex Axion on 0777 123 263 to arrange a visit and discuss air demand, compressor location, dryer and receiver requirements for your premises.
Vortex Axion (Pvt) Ltd
31, 1st Lane, Medawelikada Road, Rajagiriya, Sri Lanka.
Call 0777 123 263 or 0117 101818. Contact Vortex Axion with your application details and request confirmation of the offered Vortex Pneumatics model and complete installed scope.